Perhaps the most significant aspect of the Truss-T Hangers™ is that their design allows them to be installed from the ground. This not only makes installation significantly safer, but it also makes installation much cheaper because the cycle time for installing fixtures can be shortened dramatically.

Another important feature of the Truss-T Hangers™ is that they are aesthetically superior to the traditional hanging systems. In this respect, the traditional hanging systems lack any significant structural integrity, thereby requiring the use of chains, exposed wiring, trapezes and other creative, yet messy solutions. Truss-T Hangers™ are designed to accommodate Sch. 40 and EMT piping which will sharpen up a building's "canopy" area by giving it a clean, organized look.

INSTALLATION INSTRUCTIONS:

APPLICATION #1
Support Luminaire/ Conduit, Tubing, & Cable/ Piping with ½" NPT Threaded Coupler Top or Bottom Chord

1. Remove Truss-T Hanger unit from packaging.
2. Engage coupling to provide a 2-1/2" clearance between the bottom of the "T" and the top of the coupling.
3. Precut a section of 1/2" Schedule 40 pipe to the required length for the application.
4. Thread the pipe section into the coupling while maintaining the 2-1/2" distance outlined in Step 2.
5. While holding on to the pipe section, insert the Truss-T Hanger Assembly parallel through the center of the steel truss.
6. Rotate the Truss-T Hanger Assembly 90°clockwise while insuring the bottom of the Truss-T Hanger "T" is above the top surface of the steel truss.
7. Position the Truss-T Hanger Assembly in the proper location and hand tighten.
8. Once installed, the Truss-T Hanger Assembly may be repositioned by loosening the assembly and then hand tightening securely.
   

APPLICATION #2
Support Luminaire / Conduit, Tubing, & Cable/ Piping to Clevis Hanger with ½" NPT Threaded Coupler Top or Bottom Chord

1. Remove Truss-T Hanger unit from packaging.
2. Engage coupling to provide a 2-1/2" clearance between the bottom of the "T" and the top of the coupling.
3. Rotate the Truss-T Hanger Assembly 90° clockwise while insuring the bottom of the Truss-T Hanger "T" is above the top surface of the steel truss.
4. Position the Truss-T Hanger Assembly in the proper location and hand tighten.
5. Once installed, the Truss-T Hanger Assembly may be repositioned by loosening the assembly and then hand tightening securely.
   

APPLICATION #3
Keps® Nut / Washer Installation

1. Remove Truss-T Hanger Keps nut / washer from packaging.
2. Using your hands, thread the Keps nut / washer (clockwise) to provide a 2-1/2" clearance between the bottom of the "T" and the top of the washer.
3. Rotate the Truss-T Hanger Assembly 90° clockwise while insuring the bottom of the Truss-T Hanger "T" is above the top surface of the steel truss.
4. Position the Truss-T Hanger Assembly in the proper location and hand tighten.
5. Once installed, the Truss-T Hanger Assembly may be repositioned by loosening the assembly and then hand tightening securely.
   

APPLICATION #4
Truss-T Hanger Mounted to Top or Bottom Chord of Truss System using Keps Nut / Washer

1. Remove Truss-T Hanger square nut / washer from packaging.
2. Using your hands, thread the square nut / washer (clockwise) to provide a 2-1/2" clearance between the bottom of the "T" and the top of the washer.
3. Rotate the Truss-T Hanger Assembly 90° clockwise while insuring the bottom of the Truss-T Hanger "T" is above the top surface of the steel truss.